Instructions & FAQ's for the Home & Office

Configuring your Installation

There are two possible configurations, one if you have access to the fuse box for your home or office (preferred), and the other if you do not. (A fuse box is also known as the circuit breaker box or electrical service panel - it is the enclosure where the fuses / circuit breakers reside). If you have access to the fuse box, that is the preferred configuration.

1)  If you have access to the fuse box (preferred):

  • You will need to purchase the Home & Office Kit, which comes with one large metal plate for the fuse box, and a number of smaller ones for various outlets around the area to be covered (not all of them). These plates have adhesive backing for affixing them to the fuse box and outlets.
  • Choose the size of the kit as follows:
    • 1500 - for areas up to 139 square meters
    • 2600 - for areas from 139 to 242 square meters
    • 3700 - for areas from 242 to 344 square meters
    • 4800 - for areas from 344 to 446 square meters
    • If you have an area larger than 446 square meters, purchase one additional Home & Office Single for each additional 37 square meters
  • You should size your installation according the entire space covered by the fuse box, even if it is not often occupied (for example the garage or an unfinished basement).
  • If you have more than one fuse box, size the installation according to the entire space covered by your electricity meter.

2)  If you do not have access to the fuse box:

  • You should purchase four Home & Office Singles, which will cover a space up to 93 square meters.
  • For each additional 35 square feet meters 93 you wish to cover, you will purchase an additional Single.
  • For example, in a space of 139 square meters you would need six Singles, for 230 square meters you would need eight Singles, etc. – each additional Single adds 35 square meters to the 93 covered by the minimum four Singles.
  • You may click here to view and order the Singles.

Installing Your Home & Office

Home Office Installation Diagram

1)  If you have access to the fuse box and purchased a Home & Office Kit:

  • You will have one larger metal plate and a number of smaller ones. The number of smaller plates you receive depends on the size of the kit you ordered (1500 = 4, 2600 = 7, 3700 = 10, 4800 = 13).
  • The larger plate should be placed on the inside of your fuse box door. When the door is closed the sticker will be facing the fuses (a.k.a. circuit breakers).
  • Four of the smaller plates should be placed on outlets on the four outer walls of the space. For multi-story spaces, place the stickers opposite each other, one on the top floor and one on the bottom floor. For example, if on the bottom floor you place them on the east and north walls, on the top floor place them on the west and south walls. If you live in an apartment, the "outer walls" of the space would be the outer walls of your apartment, even if there is another apartment or a hallway on the other side of some of the walls.
  • For the additional smaller plates that you received (if applicable), place them on various outlets distributed as evenly as possible around the space on the interior walls.
  • It is not important where on the outlets the smaller plates are placed. You may even take the outlet cover off and place them on the inside.
  • The smaller plates do not need to be exactly opposite each other (outer walls) or evenly distributed (inside walls) to work effectively. Just do the best you can with the outlets you have available. You may also place them on light switches instead of outlets and they will work just as well.
  • It is not important whether there are any smaller plates near your wireless devices or near where you spend most of your time. The energy from the plates will be circulated evenly throughout the space, so their exact locations are not relevant.

2)  If you do not have access to the fuse box and purchased only Home & Office Singles:

  • Simply follow the instructions in (1) above, skipping the first two points.

Frequently Asked Questions

Can I purchase just one Home & Office Single?

  • The Home & Office system is not effective unless it is sized appropriately for the space to be covered. It works by circulating through the electrical system (not using electricity however), so it will not offer the appropriate level of protection if not configured properly (see the top of this page). Placing just one near your bed, for example, will not be effective. Nor will placing them on your wireless devices - for that you should choose the Harmonizer+ (for cell phones & WiFi routers) or the Harmonizer (for other wireless devices).

Can I move the Home & Office to a new location?

  • Yes, you may move the metal plates to a new location by removing them and re-attaching them in the new location. The adhesive backing will generally still be sticky, but if it is not you can attach them again with double-sided tape, a piece of clear tape over the top, or glue. It is best to use a razor blade when removing them to make it easier to peel off and to minimize any damage to them. Any adhesive left on the surface may be easily removed with rubbing alcohol.

How does the Home & Office improve the air quality within the protected space?

  • The Home & Office helps to restore the natural balance of negative and positive ions within the space. Most indoor spaces, especially those polluted by EMF radiation, have an unnaturally low presence of negative ions. When the natural balance is restored, fine and ultra-fine particles in the air clump together and fall to the floor. This is good for your health, since breathing the particulate matter is unhealthy. A higher concentration of negative ions generally improves the “feel” or “energy” of the space as well, which is one reason why we feel happier and more energized when outdoors in nature.

Do I also need the other EMF Harmony products for the wireless devices within the protected space?

  • All of the products are designed to work synergistically together, so ideally you would have the other products on your wireless devices. We recommend using the Harmonizer+ for your WiFi router and cell phones at least, as these are very powerful emitters of EMF radiation.